 | CO2 Controller (Stand alone)
Brand: Solatel
CO2 Controller (Stand alone) | *$658.80 |
 | CO2 Generator CD-12LP - 12 cu.ft. per hour Propane
Brand: Green Air Products
CO2 Generators operate by burning carbonaceous fuels such as propane or natural gas. The burners used in Green Air Products CO2 generators are specifically designed to maximize the production of CO2 and minimize heat as a by-product. Through the use of a constant burning pilot and equipped with a safety valve to avoid the loss of fuel should the pilot light go out, Green Air Products generators provide CO2 far more economically than any other means of enrichment. The generators may be controlled with timers, are easily installed, dependable and efficient. Transformer included. Operates on 110 volt AC. | *$512.00 |
| CO2 Generator CD-6LP - 6 cu.ft per hour Propane
Brand: Green Air Products
CO2 Generators operate by burning carbonaceous fuels such as propane or natural gas. The burners used in Green Air Products CO2 generators are specifically designed to maximize the production of CO2 and minimize heat as a by-product. Through the use of a constant burning pilot and equipped with a safety valve to avoid the loss of fuel should the pilot light go out, Green Air Products generators provide CO2 far more economically than any other means of enrichment. The generators may be controlled with timers, are easily installed, dependable and efficient. Transformer included. Operates on 110 volt AC. | *$491.10 |
 | CO2 Generator LP 3000-6000 BTU
Brand: Sentinel / GPS Part Number: SEVCG-6LP
VCG-6 LP comes complete with (2) clean burning brass burners pre-installed that produce up to 6 cubic feet / hr of CO2. Electronic ignition standard, tip-over switch standard, dual redundant solenoids standard, peace of mind STANDARD. Comes with the appropriate regulator & 10 foot hose. | *$416.60 |
 | Co2 Generator LP GEN-2E, Electronic Ignition
Brand: C.A.P. (Custom Automated Products) Part Number: CAGEN2ELP
Electronic Ignition GeneratorsGEN1LP and GEN2ENG have electronic ignition and come with 2 burners standard. GEN2ELP and GEN2ENG also have electronic ignition and come with 5 burners standard. If extra burners are needed add them to your order separately.The GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable C | *$445.99 |
 | Co2 Generator LP High Altitude 1-4 Burners
Brand: C.A.P. (Custom Automated Products) Part Number: CAGEN1ELPHA
3,100-12,500 BtuNATURAL GASThe GEN-1 is capable of producing between 3 and 13 cubic feet of CO2 per hour. It comes standard with one burner, producing approximately 3 cubic feet per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 13 cubic feet of CO2 per hour.Recommended for small to medium size areas up to 15' x 15'.LIQUID PROPANEGEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unl | *$397.00 |
 | Co2 Generator LP High Altitude 5-8 Burners
Brand: CA Part Number: CAGEN2LPHA
14,200-22,400 BtuLIQUID PROPANEThe GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unless the pilot i | *$495.00 |
| CO2 Generator NG 3000-6000 BTU
Brand: Hydrofarm Part Number: SEVCG-6NG
VCG-6 NG (Natural Gas) comes complete with (2) clean burning brass burners pre-installed that produce up to 6 cubic feet / hr of CO2. Electronic ignition standard, tip-over switch standard, dual redundant solenoids standard, peace of mind STANDARD. Comes with the appropriate regulator & 10 foot hose. | *$416.60 |
 | CO2 Generator, Lp, 1-4 Burners, 2,700-11,200 BTU
Brand: C.A.P. (Custom Automated Products) Part Number: CAGEN1LP
2,700-11,200 BtuElectronic Ignition GeneratorsGEN1LP and GEN2ENG have electronic ignition and come with 2 burners standard. GEN2ELP and GEN2ENG also have electronic ignition and come with 5 burners standard. If extra burners are needed add them to your order separately.The GEN-1 is capable of producing between 3 and 13 cubic feet of CO2 per hour. It comes standard with one burner, producing approximately 3 cubic feet per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 13 cubic feet of CO2 per hour.Recommended for small to medium size areas up to 15' x 15'.LIQUID PROPANEGEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some | *$291.90 |
| CO2 Generator, Lp, 5-8 Burners, 14,200-22,400 BTU
Brand: C.A.P. (Custom Automated Products) Part Number: CAGEN2LP
14,200-22,400 BtuLIQUID PROPANEThe GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unless the pilot i | *$495.00 |
 | Co2 Generator, LP: 6000-27000 Btu
Brand: Sentinel / GPS Part Number: SEVCG-27LP
VCG-27 LP (propane) comes complete with (10) clean burning brass burners pre-installed that produce from 6 up to 27 cubic feet / hr of CO2. Two selector valves make setting the output easy. Electronic ignition standard, tip-over switch standard, dual redundant solenoids standard, peace of mind STANDARD. Comes with the appropriate regulator & 10 foot hose. | *$649.00 |
| Co2 Generator, NG High Altitude 1-4 Burners
Brand: CA Part Number: CAGEN1ENGHA
3,100-12,500 BtuNATURAL GASThe GEN-1 is capable of producing between 3 and 13 cubic feet of CO2 per hour. It comes standard with one burner, producing approximately 3 cubic feet per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 13 cubic feet of CO2 per hour.Recommended for small to medium size areas up to 15' x 15'.LIQUID PROPANEGEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unl | *$430.65 |
| Co2 Generator, NG High Altitude 5-8 Burners
Brand: CA Part Number: CAGEN2ENGHA
14,200-22,400 BtuLIQUID PROPANEThe GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unless the pilot i | *$546.80 |
| CO2 Generator, Ng, 5-8 Burners, 15,900-25,300 BTU
Brand: C.A.P. (Custom Automated Products) Part Number: CAGEN2NG
15,900-25,300 BtuNATURAL GASThe GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unless the pilot is l | *$495.00 |
 | Co2 Generator, NG, High Altitude, 5-8 Burners
Brand: CA Part Number: CAGEN2NGHA
15,900-25,300 BtuNATURAL GASThe GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity up to approximately 26 cubic feet of CO2 per hour. Recommended for larger areas up to 30' x 30'.GEN-1 / GEN-2 Propane or Natural Gas Generators Carbon Dioxide (CO2) is one of the easiest ways to accelerate plant growth, producing up to 40% more flowers or fruit. A propane or natural gas CO2 generator is the most cost effective way to add CO2 to your environment. Many greenhouses use CO2 generators to boost CO2 levels safely and economically. C.A.P. has developed some of the safest and most reliable CO2 Generators; capable of producing between 3 and 26 cubic feet of CO2 per hour. Both the GEN-1 and the GEN-2 units feature a "two-stage" safety pilot valve, which will not allow fuel to flow to the burner unless the pilot is l | *$495.00 |
 | Co2 Generator, NG: 3000-6000 Btu - High Altitude
Brand: Sentinel / GPS Part Number: SEVCG-6NGHA
Variable CO2 output from 3 to 6 cubic foot CO2 / Hr. Solid state electronic ignition control module eliminates the open pilot flame Tip-over switch shuts off the gas flow in the event the unit falls or tips over Unit comes standard with 2 brass burners pre-installed The burners are designed to burn clean and produce consistent blue flames Dual redundant low-voltage solenoid valves add a second layer of safety Comes complete with 12 foot hose and pressure regulator | *$416.60 |
| Co2 Generator, NG: 6000-27000 Btu
Brand: Sentinel / GPS Part Number: SEVCG-27NG
VCG-27 NG (natural gas) comes complete with (10) clean burning brass burners pre-installed that produce from 6 up to 27 cubic feet / hr of CO2. Two selector valves make setting the output easy. Electronic ignition standard, tip-over switch standard, dual redundant solenoids standard, peace of mind STANDARD. Comes with the appropriate regulator & 10 foot hose. | *$634.30 |
 | Co2 Generator, NG: 6000-27000 Btu - High Altitude
Brand: Sentinel / GPS Part Number: SEVCG-27NGHA
Variable CO2 output from 6 to 27 cubic foot CO2 / Hr. Solid state electronic ignition control module eliminates the open pilot flame Tip-over switch shuts off the gas flow in the event the unit falls or tips over Unit comes standard with 10 brass burners pre-installed The burners are designed to burn clean and produce consistent blue flames Dual redundant low-voltage solenoid valves add a second layer of safety Comes complete with 12 foot hose and pressure regulator | *$576.20 |
 | CO2 monitor w/PPM sensor for CO2-2, CO2-4 & CGC-1
Brand: C.A.P. (Custom Automated Products) Part Number: CAPPM1C
The PPM-1c is an extremely accurate CO2 sensor. It measures the exact level of CO2 in your growing area and displays this value from 0 to 5000 Parts-Per-Million (PPM) on its digital readout. | *$369.89 |
 | Co2 Regulator & Valve
Brand: C.A.P. Part Number: REG-1
The C.A.P. CO2 Regulator/Emitter will allow you to maintain ideal CO2 levels for optimum growth. It features an accurate, easy to adjust CO2 flow meter, a pre-set regulator that never needs adjusting, and solenoid valve. Each unit also comes with the tubing needed to disperse the CO2 evenly throughout your room by attaching the tubing to the back of an oscillating fan for even dispersion. If you are using this without a digital CO2 controller, you will need to use a timer. The flow rate is adjustable from .5 - 15 Cubic Feet Per Hour. | *$79.99 |
 | CO2 Set Point Controller Model SPC-1
Brand: Green Air
This new easy to install and to operate CO2 enrichment controller is factory calibrated and inspected for optimum performance. The SPC-1 is designed with a photo sensor to defeat CO2 enrichment during dark periods and a large easy to read real-time LED display. The SPC-1 also is programmed with a preset differential (hysteresis) of 20 PPM and offers an elevation adjustment feature to fine tune performance. Quick Start Installation Instructions are available in English and Espaol. Like all of Green Air Products high quality controllers, the SPC-1 is constructed with durable components and a rust and scratch resistant, black anodized aluminum chassis to ensure that this controller will perform as expected for years to come. Operates on 120 Volt AC with 12 Amp switching capacity. | *$507.55 |
 | CO2-2e - 2 Timer CO2 Controller
Brand: CA Model: CO2-2e Part Number: CO2-2e
These controllers make it easy to coordinate your exhaust and CO2 production. The 2 Timer CO2 Controller CO2-2e has 2 timers that allow for efficient control of CO2 levels, one controls how often CO2 is released and the other controls how long it is released. It also features temperature and humidity controls that will stop CO2 production and activate the exhaust outlet if the levels that you set are exceeded. A photosensor disables CO2 production while the lights are off. The 4 Timer CO2 Controller CO2-4e has the same features as the CO2-2e, but includes 2 extra timers. The CO2-4e features an Overall Cycle Timer that controls the maximum time between exhaust cycles. It also has an Exhaust Cycle Timer to control how long the exhaust fans will run. Both units are expandable to PPM?level CO2 control with the addition of the PPM-1c CO2 monitor/controller. They are both rated for 15 amps @ 120 volt. 5 year no hassle manufacturers warranty. | *$249.89 |
 | CO2/PPM Monitor
Brand: Atlantis Hydroponics
The CO2 PPM Monitor measures the level of carbon dioxide in an indoor garden from 0-5000 parts-per-million (ppm) and displays the readings on a digital readout. Indoor growers can pair it with the 2 or 4 Timer CO2 Controller or the Complete Greenhouse Controller, enter the exact level of CO2 required, and the monitor will measure the levels and command their attached unit to produce more when levels fall. Monitor will work with any 120-volt CO2 valve or generator. Controller carries a three-year warranty. contains 1 per box | *$499.98 |
 | CO2/RH/Temp Controller Day/Night Settings, 6 Equipments
Brand: Intelligent Growing Systems (Plug & Grow Part Number: NBIGS221
CO2/RH/Temp Controller Day/Night Settings, 6 Equipments | *$1,062.00 |
 | CO2/RH/Temperature Smart Controller
Brand: Intelligent Growing Systems (Plug & Grow Part Number: NBIGS220
Seamless intergrationof Co2 enrichment and intake/exhaust ventilation.Co2, relative humidity and temperature precise electronic sensors.24 hour datalogging of sensor values.Alarm system hook-up (with iMS-100). | *$923.94 |
 | CO24E Co2 & Atmosphere Controller
Brand: C.A.P. Model: CO24E Part Number: CO24E
The CO2-4e has four timers that are used to control your CO2.to add just the right amount of CO2 without the wasteful "overshoot" that other controllers have. One timer controls the length of time the CO2 is released and another controls how often the CO2 is released. The result is a very efficient method of controlling CO2. The "Overall Cycle timer" allows the user to decide how long the supplemental CO2 is kept in the growing area prior to being exhausted. When the "Overall Cycle" time expires, the CO2-4e turns ON the exhaust outlets and enables the "Exhaust Cycle Timer", which controls the amount of time the exhaust fans will run. When complete, the cycle is reset and the CO2 cycle starts again. It also features temperature and humidity controls which will disable CO2 injection if the temperature or humidity levels that you specify are exceeded, activating an exhaust outlet which can control ventilation equipment (air conditioner, fan, etc.) It also has a built in photo controller, which disables the CO2 function when the lights are off. The CO2-4e can also be used with the PPM-1c sensor for unequalled Parts-Per-Million performance. The CO2-4e is rated for 15 amps @ 120 volts. | *$289.45 |
 | Cold Steel Kukri Machete with PVC Handle
Brand: Cold Steel Model: 97KMS Part Number: 97KMS
Our Kukri Machetes are those workhorses. They are available in two sizes, one has a thirteen inch blade and the other, our new “Magnum” model has a whopping seventeen inch blade. Both are ready to plow through the toughest chores life can dish out. Each features the distinctive weight-forward balance of our “top-of-the-line” models, and always present their edge on an angle so they’re guaranteed to “bite” deep with every stroke. Additionally, they come complete with a sturdy Cordura sheath! They're a solid value, ready for long, hard work. | *$14.58 |
 | Cold Steel Magnum Kukri Machete (Cordura Sheath)
Brand: Cold Steel Model: 97MKM Part Number: 97MKM
Our Kukri Machetes are those workhorses. They are available in two sizes, one has a thirteen inch blade and the other, our new “Magnum” model has a whopping seventeen inch blade. Both are ready to plow through the toughest chores life can dish out. Each features the distinctive weight-forward balance of our “top-of-the-line” models, and always present their edge on an angle so they’re guaranteed to “bite” deep with every stroke. Additionally, they come complete with a sturdy Cordura sheath! They're a solid value, ready for long, hard work. | *$16.74 |
 | Cold Steel Rifleman's Hawk American Hickory Handle
Brand: Cold Steel Model: 90RH Part Number: 90RH
This superb tomahawk features a factory-honed cutting edge. It has two sticking points on its cutting edge for throwing and throws extremely well. The Rifleman’s Hawk has a traditional American hammer-head style butt for hammering stakes | *$22.14 |
 | Cold Steel Special Forces Shovel with Hardwood Handle
Brand: Cold Steel Model: 92SF Part Number: 92SF
The Special Forces Shovel is modeled after the original Soviet Spetznaz shovel. The Spetznaz soldiers made up the most elite unit in the Soviet Army. The U.S. equivalent would be our Green Berets. The shovel head and socket are forged from medium carbon steel, then heat treated for maximum strength. The edges come sharpened to a utility/axe edge that can easily be improved to razor sharpness. | *$15.12 |
 | Cold Steel Special Forces Shovel, Hardwood Handle
Brand: Cold Steel Model: CS92SF & CSSC92SF Part Number: 92SF
ATTRIBUTESÂ Overall Length (inches):Â 20.50Â Special Features:Â Shovel Head And Socket Are Forged From Medium Carbon Steel Then Heat Treated For Maximum Strength And Feature A Durable Solid Hardwood Handle | *$18.99 |
 | Cold Steel Trail Boss Hickory Handle
Brand: Cold Steel Model: 90TA Part Number: 90TA
The Trail Boss is light and compact enough to carry all day in your hand or strapped to your pack, yet heavy and tough enough for chores that would make a hatchet or tomahawk scream for mercy. Featuring a European style head with a 4" blade and a 4 1/2" cutting edge, it takes a big bite with every swing. Plus, it features a very stout straight-grained Hickory handle. Extensively field-tested by Lynn C. Thompson on a month long hunting trip in the outback of Australia, the Trail Boss was really put to the test. He used it to chop kindling, clear roads and trails, to build blinds and even to chop down a fair sized Gidgee Tree (one of the hardest woods found down under). | *$23.99 |
 | Cold Steel Trail Hawk American Hickory Handle
Brand: Cold Steel Model: 90TH Part Number: 90TH
Modeled after an early frontier pattern, our Trail Hawk can do it all. It's an excellent chopper and has a functional hammer poll with a hardened face so you can drives nails, hammer in stakes, and smash or crush just about anything. Best of all it's extremely lightweight and compact so it's a cinch to tuck it under your belt or lash it to a pack or shooting bag. | *$22.74 |
 | Cold Steel Trench Hawk Axe
Brand: Cold Steel Model: 90PTH Part Number: 90PTH
The Trench Hawk may well be the perfect antidote to the raw terror of eyeball to eyeball combat in the confined spaces of a trench, bunker, alley or narrow hallway. All it takes is one stroke from either the vicious cutting edge or its brutal wedge shaped spike to end the fight, and if the party starts at longer range the Trench Hawk's twin -Inchbusiness ends-Inch make an accurate throw a breeze, since there's double the chance of a lethal hit. When used defensively, the Trench Hawk's cutting edge and spike also provide a big advantage, as either can be used for hooking or trapping and, like our Spike Hawk, their combined length can be used to parry or block an incoming blow. Drop forged from 5150 carbon steel and differentially hardened, the head of the Trench Hawk will withstand tremendous blows and the awful stress of continued throwing. | *Too low to display |
 | Cold Steel Two Handed Katana Machete Sheath Cover
Brand: Cold Steel Model: SC97THK Part Number: 008804
Have you ever longed to pick up your expensive, high performance Samurai sword and run amok through the woods stabbing, cutting, chopping and hacking every inanimate object in sight without the fear of losing all your hard earned money by damaging it?That's why we created the Katana Machete. Made in our factory in South Africa, it offers a 19" long blade with a modified Tanto style point. Heat treated to a tough spring temper and sporting a black, baked-on anti-rust finish, it comes with a good utility edge that can easily be fully sharpened. To facilitate one or two-handed use, we have paired the blade with a long handle, complete with a sturdy cross guard. Injection molded over the blade's tang, and further secured by two thick bolts, it shrugs off hard knocks and defies the elements. | *$6.21 |
 | Columbia River Knife and Tool's 2013 Razel SS7 Chisel with Bellied Razor and Veff Serrated Blade
Brand: Columbia River Knife and Tool (CRKT) Model: 2013 Part Number: CR2013
Razel SS7 Chisel Double Edge Micarta Handle Sheath | *Too low to display |
 | Columbia Sinks Stainless Steel Reinforced Drag Fork, 4 Tines - 9" Long, Overall Length 60"
Brand: Columbia Sinks Part Number: 2075R
Features of the Columbia Sinks Stainless Steel Fork: Tough and durable stainless makes these forks ideal for moving bulk materials. Electropolished and passivated to enhance corrosion resistance. Reinforced support bracket. The product referenced on this detail page is sold be Each. | *$164.59 |
 | COMBO METER/BLUELAB
Brand: Bluelab Part Number: BLU2300E
Light weight and portable Measures pH, Nutrient and Temperature Three display options for nutrient - EC, CF, ppm (500 scale) Two display options for temperature (C or F) Three calibration points, 4, 7 and 10 pH Temperature at a push of a button Simple push button pH calibration Auto turn off function Large 13mm (1/2) digital display for easy reading Supplied with quality probes and pH calibration solutions Low battery indicator Long life 3 AAA batteries 5 year Bluelab Guarantee (6 mo for pH probe) | *$278.40 |
 | Compact Pruner Carded Case Pack 12
Brand: Dramm Part Number: 901619
Compact Pruner Carded - Perfect pruner for trimming woods stems and perennials. Corrosion-resistant stainless steel blades have a maximum .25'''' cutting capacity. Ergonomically designed for comfortable, strong use. Available in an array of six vibrant colors: red, orange, yellow, green, blue and berry.'' Case Pack 12 | *$237.46 |
 | Compact Water Chiller - 1/10 HP
Brand: EcoPlus Part Number: 1/10 HP
During the summer months tap water and nutrient solution temperatures can easily reach above 80°F. This can pose a problem with nutrient uptake and also increasing the chance of root rot outbreaks. Hydroponic Systems can also heat up due to high-intensity lighting, pump heat or during hot summer months. For maximum production and highest dissolved oxygen, the nutrient solution temperature should remain between 68 and 75°F. The Eco Plus Water Chiller will help hydroponic gardeners to achieve this optimal temperature range with its internal micro computer and digital LCD display for easy operation. The efficiency of this unit it outstanding and is capable of lowering the temperature of 93 gallons of water by 10°F or 35 gallons by 30°F. The corrosion-resistant titanium heat exchanger is ideally suited for hydroponic nutrient solutions.Features Micro computer with digital LCD display allow for easy operation High quality Japanese-made compressor is extremely efficient and reliable compact size and easy to move comes standard with 1/2 fittings suitable for cooling both fresh and salt water features a titanium heat exchanger for optimum performance and corrosion resistance Specifications: power: 1/10 hp voltage: 120v/60Hz wattage: 280 amps: 2.3 BTUs: 950 product weight: 31 lbs dimensions: 10.5W x 12D x 14H pump size: 132gph min - 264gph max chilling capacity: 93 gallons - 10°F; 35 gallons - 30°F | *$397.99 |
 | Compact Water Chiller - 1/4 HP
Brand: EcoPlus Part Number: 1/4 HP
During the summer months tap water and nutrient solution temperatures can easily reach above 80°F. This can pose a problem with nutrient uptake and also increasing the chance of root rot outbreaks. Hydroponic Systems can also heat up due to high-intensity lighting, pump heat or during hot summer months. For maximum production and highest dissolved oxygen, the nutrient solution temperature should remain between 68 and 75°F. The Eco Plus Water Chiller will help hydroponic gardeners to achieve this optimal temperature range with its internal micro computer and digital LCD display for easy operation. The efficiency of this unit it outstanding and is capable of lowering the temperature of 170 gallons of water by 10°F. The corrosion-resistant titanium heat exchanger is ideally suited for hydroponic nutrient solutions.Features Micro computer with digital LCD display allow for easy operation High quality Japanese-made compressor is extremely efficient and reliable compact size and easy to move comes standard with 3/4 fittings suitable for cooling both fresh and salt water features a titanium heat exchanger for optimum performance and corrosion resistance Specifications: power: 1/4 hp voltage: 120v/60Hz wattage: 480 amps: 4 BTUs: 2200 product weight: 48.5 lbs dimensions: 13W x 15D x 16H pump size: 633gph min - 1056gph max chilling capacity: 170 gallons - 10°F; 100 gallons - 30°F | *$500.00 |
 | Complete Greenhouse Controller w/PPM option
Brand: C.A.P. Part Number: CACGC1
The CGC-1 Complete Electronic Greenhouse Controller controls all of the main devices required in today's modern hydroponic garden. Your HID lights, supplemental CO2, hydroponic pumps, exhaust fans or air conditioner.C.A.P. strongly believes that the only way to design and manufacture controllers is the right way. That means understanding what expectations customers have, and manufacturing controllers that meet or exceed their expectations. It means paying attention to details and not cutting corners; constantly striving to produce the most innovative products in the industry, using only the finest quality components to ensure many years of trouble-free operation.CAP WARRANTYCAP controls are warranted to be either rebuilt or replaced at the manufacturer's determination for a period of 3 years of normal use.Modification, misuse or abuse voids this warranty. | *$379.95 |
 | Compost Tea System - 10 Gallons
Brand: Growing Solutions Part Number: GSI S10
The is a tea brewer that is ideal for homeowners, small nursery operations and research environments. This model delivers reliable performance with greater portability and convenience. The patented Compost Tea System is designed for durability, ease of use, and years of safe and consistent operation. This 10 gallon tea brewer features a patented design, industrial grade components, easy maintenance and fine bubble diffusion technology. Fine bubble diffusion technology is a constant dynamic aeration process. Each fine bubble diffusion aeration disc has more than 4,000 engineered perforations that provide consistent air bubble size and velocity. This constant aeration process ensures maximum oxygen transfer efficiency, creating an optimum environment for reproduction of beneficial microorganisms. The compost tea solution is thoroughly mixed by the fine bubble diffusion aeration process inside the tank, eliminating the need for external agitation. Each disc's perforations self-seal when the system is off, preventing back flow of compost tea into the air manifold. More than 4,000 1mm perforations in our fine bubble diffusion discs ensure optimum oxygen levels are maintained while providing thorough mixing of the compost tea solution. After 24 hours, the compost tea brewing cycle is complete. Use your compost tea as soon as possible as it contains living microorganisms. Apply as a foliar spray or soil drench with a sprayer, watering can or other application equipment. | *$549.00 |
 | Continuous pH/TDS/temp Monitor
Brand: Hanna Instruments Part Number: HI9815047
Designed for continuous monitoring of pH, TDS and temperature the HI 981504 is simple to install and can be placed above the sample to be tested. pH, TDS and temperature measurements are simultaneously displayed on three backlit LCDs which can be easily viewed at a distance - even in low light. This means no more switching between parameters.The HI 1286 gel-filled pH electrode is provided with a waterproof sheath to protect the BNC connector. The unique design of the electrode provides longer life in aggressive solutions. The HI 7634 TDS probe is easy to clean and requires little maintenance. Measurements are accurate and the meter can be calibrated at one or two points for pH and at a single point for TDS. Temperature range is factory calibrated. | *$219.71 |
 | Copper Watering Can
Brand: Joshua Roth Model: 2099 Part Number: 2099
This solid copper, 1.8 liter watering can has hand-soldered seams. Ulta fine sprinkling rosette sprays a velvet mist, especially well suited for delicate floral and bonsai tasks. Comes with an additional 7" interchangeable spout. 26" overall with rosette. | *$179.95 |
 | Corona Clipper 1-Inch Capacity Bypass Pruner With Vinyl Coated Aluminum Handles BP 6250
Brand: Corona Clipper Model: BP 6250 Part Number: CRNBP6250
<P>Bypass Pruner </P> <UL> <LI>Lightweight Forged aluminum construction Cuts up to 1"</LI> <LI>Easy to replace high carbon steel blade </LI> <LI>Slant ground narrow profile hook with self cleaning sap groove</LI> <LI>Lifetime warranty </LI> <LI>Ishock abs | *$34.28 |
 | Corona Clipper 10-inch Curved Blade Folding Razor Tooth Saw RS 7265
Brand: Corona Clipper Model: RS 7265 Part Number: RS 7265
The first choice of landscape professionals. Extra long, 10" forged blade with limb notch, fully heat treated for strength. Wood handle with shock absorber. Weight 3 lbs. | *$18.03 |
 | Corona Clipper 20-Inch Raker Tooth Pruning Saw PS 4081
Brand: Corona Clipper Model: PS 4081 Part Number: GT0595
For large branches. Specially designed to cut live green wood. Laminated hardwood D-style handle. 20 inch blade with self-cleaning raker tooth pattern. Curved blade design for faster cutting. Tempered steel alloy blade. Four precision-ground teeth per inc | *$36.99 |
 | Corona Clipper 21-inch Bypass Lopper with StrataShear Blade Cuts Up To 1 1/2-inch AL 8120
Brand: Corona Clipper Model: AL 8120 Part Number: AL 8120
Professional Stratashear Bypass Lopper, 1-1/2 Diameter Cutting Capacity, 21' Overall Length, Lightweight, High Srength Spin On/Off Elliptical Aluminum Handles, Resharpenable, Replaceable Radial Arc Bypass Blade Of Fully Heat Treated Forged Coronium Steel Alloy, Cuts Up To 32% Easier, Forged Slant Ground Hook With Sel Cleaning Sap Groove, Comfortable Ergonomic Grips, Lifetime Warranty. | *$39.00 |
 | Corona Clipper 21-Inch Razor Tooth Raker Saw RS 7160
Brand: Corona Clipper Model: RS 7160 Part Number: 403675
Corona Razor Tooth Saw The Corona Razor Tooth Saw is great for cutting large branches and limbs. The saw features 3-Sided razor teeth, on a 7" or 21" blade. The self-cleaning raker tooth pattern reduces maintenance, while the impulse-hardened teeth give you a long service life. The saw features tempered-steel alloy construction with a precision-milled, laminated wood D handle. . 27in. overall length . 3-sided razor teeth with a self-cleaning raker pattern . Tempered steel alloy construction, D-style handle cuts on pull stroke Item Specifications: Size: 7" 21'' Warranty: Limited lifetime warranty Ships Quickly! Manufactured by Corona: Founded in the early 1920s, Corona Clipper, Inc., is a leader in the marketing and manufacturing of professional and consumer tools for the lawn and garden. With a retail and distribution network that extends throughout the United States and Canada, Corona's proven designs, quality manufacturing processes, and unparalleled customer service make it the best choice in tools for contractors, agricultural professionals, and avid gardeners alike. | *$40.76 |
